DDR Version 1.04 20130517 In DDR3 300MHz Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=8 Size=1024MB Memory OK OUT BUILD=====2 SdmmcInit=0 0 FwPartOffset=2000 , 0 run on sd0 OK! 27950 unsigned! SecureBootEn = 0 0 Boot ver: 0000-00-00#0.00 start_linux=====41962 447387 Starting kernel...@0x60408000 Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.36+ (root@PLATINUMONE) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 SMP PREEMPT Sat Jun 28 18:43:20 EST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: RK30board [ 0.000000] ddr size = 1024 M, set ion_reserve_size size to 125829120 [ 0.000000] memory reserve: Memory(base:0x98800000 size:120M) reserved for [ 0.000000] memory reserve: Memory(base:0x97000000 size:24M) reserved for [ 0.000000] memory reserve: Total reserved 144M [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] CPU SRAM: copied sram code from c0b18000 to fef00100 - fef02138 [ 0.000000] CPU SRAM: copied sram data from c0b1a038 to fef02138 - fef02a74 [ 0.000000] sram_log: 4q ?& : 4q ?) !?, # 0q *! ! 3q @ 3q [ 0.000000] CLKDATA_MSG: pll_flag = 0x03 [ 0.000000] cpll auto set rate error [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B [ 0.000000] DDR DEBUG: version 1.00 20131106 [ 0.000000] DDR DEBUG: DDR3 Device [ 0.000000] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB [ 0.000000] DDR DEBUG: init success!!! freq=300MHz [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x3, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=0 extra clock, DGPS=360 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=0 extra clock, DGPS=360 [ 0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0 [ 0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb [ 0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2 [ 0.000000] PERCPU: Embedded 7 pages/cpu @c1dd2000 s7008 r8192 d13472 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 223232 [ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x001A0000 mtdparts=rk29xxnand:0x00002000@0x00002000(misc),0x00008000@0x00004000(kernel),0x00008000@0x0000c000(boot) bootver=0000-00-00#0.00 firmware_ver=4.4.2 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 880MB = 880MB total [ 0.000000] Memory: 872488k/872488k available, 176088k reserved, 401408K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB) [ 0.000000] vmalloc : 0xdf000000 - 0xfe800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde800000 ( 488 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0408000 - 0xc0432000 ( 168 kB) [ 0.000000] .text : 0xc0432000 - 0xc0aad880 (6639 kB) [ 0.000000] .data : 0xc0aae000 - 0xc0b17de8 ( 424 kB) [ 0.000000] .bss : 0xc0b1b024 - 0xc15c82e8 (10933 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:352 [ 0.000000] rk30_gpio_init: 128 gpio irqs in 4 banks [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] rk_timer: version 1.3 [ 0.000000] Console: colour dummy device 80x30 [ 0.008738] Calibrating delay loop (skipped) preset value.. 1583.48 BogoMIPS (lpj=7917420) [ 0.017864] pid_max: default: 32768 minimum: 301 [ 0.023208] Mount-cache hash table entries: 512 [ 0.028831] Initializing cgroup subsys debug [ 0.033585] Initializing cgroup subsys cpuacct [ 0.038566] Initializing cgroup subsys freezer [ 0.043537] CPU: Testing write buffer coherency: ok [ 0.129726] CPU1: Booted secondary processor [ 0.169719] CPU2: Booted secondary processor [ 0.209717] CPU3: Booted secondary processor [ 0.209753] Brought up 4 CPUs [ 0.227333] SMP: Total of 4 processors activated (6333.93 BogoMIPS). [ 0.234727] devtmpfs: initialized [ 0.244860] NET: Registered protocol family 16 [ 0.249921] last_log: 0xde100000 map to 0xdf004000 and copy to 0xc0b1f1a0 (version 2.1) [ 0.274032] DVFS MSG: AVS Value(index=0): 192 192 192 192 192 192 192 192 192 192 [ 0.292847] ------------[ cut here ]------------ [ 0.298043] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x48/0x1ac() [ 0.306752] autorequest GPIO-175 [ 0.310422] [] (unwind_backtrace+0x0/0xe0) from [] (warn_slowpath_common+0x4c/0x64) [ 0.320871] [] (warn_slowpath_common+0x4c/0x64) from [] (warn_slowpath_fmt+0x2c/0x3c) [ 0.331511] [] (warn_slowpath_fmt+0x2c/0x3c) from [] (gpio_ensure_requested+0x48/0x1ac) [ 0.342338] [] (gpio_ensure_requested+0x48/0x1ac) from [] (gpio_direction_output+0x80/0x23c) [ 0.353656] [] (gpio_direction_output+0x80/0x23c) from [] (machine_rk30_board_init+0x50/0x2f8) [ 0.365155] [] (machine_rk30_board_init+0x50/0x2f8) from [] (customize_machine+0x1c/0x28) [ 0.376193] [] (customize_machine+0x1c/0x28) from [] (do_one_initcall+0x90/0x160) [ 0.386456] [] (do_one_initcall+0x90/0x160) from [] (kernel_init+0x94/0x13c) [ 0.396230] [] (kernel_init+0x94/0x13c) from [] (kernel_thread_exit+0x0/0x8) [ 0.406021] ---[ end trace 1b75b31a2719ed1c ]--- [ 0.411210] ------------[ cut here ]------------ [ 0.416394] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x48/0x1ac() [ 0.425115] autorequest GPIO-174 [ 0.428769] [] (unwind_backtrace+0x0/0xe0) from [] (warn_slowpath_common+0x4c/0x64) [ 0.439225] [] (warn_slowpath_common+0x4c/0x64) from [] (warn_slowpath_fmt+0x2c/0x3c) [ 0.449874] [] (warn_slowpath_fmt+0x2c/0x3c) from [] (gpio_ensure_requested+0x48/0x1ac) [ 0.460709] [] (gpio_ensure_requested+0x48/0x1ac) from [] (gpio_direction_output+0x80/0x23c) [ 0.472026] [] (gpio_direction_output+0x80/0x23c) from [] (machine_rk30_board_init+0x5c/0x2f8) [ 0.483532] [] (machine_rk30_board_init+0x5c/0x2f8) from [] (customize_machine+0x1c/0x28) [ 0.494557] [] (customize_machine+0x1c/0x28) from [] (do_one_initcall+0x90/0x160) [ 0.504817] [] (do_one_initcall+0x90/0x160) from [] (kernel_init+0x94/0x13c) [ 0.514587] [] (kernel_init+0x94/0x13c) from [] (kernel_thread_exit+0x0/0x8) [ 0.524362] ---[ end trace 1b75b31a2719ed1d ]--- [ 0.529831] warning:lcdc0 not add to system! [ 0.534627] lcdc1 is used as primary display device controller! [ 0.641423] rk29sdk_wifi_bt_gpio_control_init: init finished [ 0.649141] console [ttyFIQ0] enabled, bootconsole disabled [ 0.649141] console [ttyFIQ0] enabled, bootconsole disabled [ 0.658262] Registered FIQ tty driver de03dcc0 [ 0.658833] Loaded driver for PL330 DMAC-1 rk29-pl330 [ 0.658877] DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 0.659063] Loaded driver for PL330 DMAC-2 rk29-pl330 [ 0.659126] DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14 [ 0.690960] bio: create slab at 0 [ 0.695405] SCSI subsystem initialized [ 0.695639] usbcore: registered new interface driver usbfs [ 0.695757] usbcore: registered new interface driver hub [ 0.709984] usbcore: registered new device driver usb [ 0.710233] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter [ 0.710481] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter [ 0.710697] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter [ 0.710839] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter [ 0.710978] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter [ 0.741573] rk30-adc rk30-adc: rk30 adc: driver initialized [ 0.741676] RK29 Watchdog Timer, (c) 2011 Rockchip Electronics [ 0.741892] rk29-wdt rk29-wdt.0: starting watchdog timer [ 0.742171] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.742627] Bluetooth: Core ver 2.16 [ 0.742695] NET: Registered protocol family 31 [ 0.742731] Bluetooth: HCI device and connection manager initialized [ 0.742782] Bluetooth: HCI socket layer initialized [ 0.742827] Bluetooth: L2CAP socket layer initialized [ 0.742881] Bluetooth: SCO socket layer initialized [ 0.743995] rk fb probe ok! [ 0.744321] i2c i2c-1: No ack, Maybe slave(addr: 0x5a) not exist or abnormal power-on, retry 2... [ 0.744615] i2c i2c-1: No ack, Maybe slave(addr: 0x5a) not exist or abnormal power-on, retry 1... [ 0.744907] i2c i2c-1: No ack, Maybe slave(addr: 0x5a) not exist or abnormal power-on, retry 0... [ 0.744972] The device is not act8846 [ 0.745034] i2c-core: driver [act8846] using legacy suspend method [ 0.745082] i2c-core: driver [act8846] using legacy resume method [ 0.745149] Switching to clocksource rk_timer [ 0.749156] Switched to NOHz mode on CPU #0 [ 0.749755] Switched to NOHz mode on CPU #3 [ 0.749775] Switched to NOHz mode on CPU #1 [ 0.749792] Switched to NOHz mode on CPU #2 [ 0.752523] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xdf0ac000 [ 0.752612] fb0:win0 [ 0.752618] fb1:win1 [ 0.752623] fb2:win2 [ 0.752720] rk3188 lcdc1 clk enable... [ 0.777836] rk3188 lcdc1 clk disable... [ 0.837526] fb0:phy:97000000>>vir:e0000000>>len:0x1800000 [ 0.837796] rk_fb_register>>>>>fb0 [ 0.838127] rk_fb_register>>>>>fb1 [ 0.838158] rk3188 lcdc1 probe ok! [ 0.895688] cfg80211: Calling CRDA to update world regulatory domain [ 0.902545] IT66121 probe success. [ 0.909250] emmc emmc: internal_storage is NOT emmc [ 0.909472] NET: Registered protocol family 2 [ 0.909629] IP route cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.910017] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.911037] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.912165] TCP: Hash tables configured (established 65536 bind 65536) [ 0.912214] TCP reno registered [ 0.912245] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.912305] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.912651] NET: Registered protocol family 1 [ 0.912832] Unpacking initramfs... [ 0.999226] Freeing initrd memory: 1664K [ 0.999331] PMU: registered new PMU device of type 0 [ 0.999473] efuse_version_val: efuse version = 51 [ 0.999513] DVFS MSG: core: dvfs_adjust_table_lmtvolt get leakage_level = 20000 [ 0.999567] efuse_version_val: efuse version = 51 [ 0.999613] DVFS MSG: aclk_gpu: dvfs_adjust_table_lmtvolt get leakage_level = 20000 [ 0.999681] DVFS ERR: gpu can't get regulator in clk_enable_dvfs [ 0.999740] DVFS ERR: dvfs(gpu) is not register regulator [ 0.999783] DVFS ERR: ddr can't get regulator in clk_enable_dvfs [ 0.999830] DVFS ERR: cpu can't get regulator in clk_enable_dvfs [ 0.999875] DVFS ERR: dvfs(cpu) is not register regulator [ 1.061297] rk3188 cpufreq version 2.2, suspend freq 816 MHz [ 1.067124] highmem bounce pool size: 64 pages [ 1.067259] ashmem: initialized [ 1.075753] fuse init (API version 7.16) [ 1.075960] msgmni has been set to 923 [ 1.083988] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.084035] io scheduler noop registered [ 1.084068] io scheduler deadline registered [ 1.084126] io scheduler cfq registered (default) [ 1.104382] rga: Driver loaded succesfully [ 1.104603] rk_serial.c v1.6 2013-12-23 [ 1.104684] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0 [ 1.104856] rk_serial rk_serial.0: membase 0xdf0c4000 [ 1.104918] rk_serial.3: ttyS3 at MMIO 0x20068000 (irq = 69) is a rk29_serial.3 [ 1.105054] rk_serial rk_serial.3: membase 0xdf0c8000 [ 1.105293] Rockchip ion module(version: 1.0) is successfully loaded [ 1.107043] loop: module loaded [ 1.107089] Android kernel panic handler initialized (bind=kpanic) [ 1.107567] PPP generic driver version 2.4.2 [ 1.107766] PPP Deflate Compression module registered [ 1.107798] PPP BSD Compression module registered [ 1.142781] ******** Show Sink Info ******** [ 1.142809] Support video mode: [ 1.142829] 1920x1080p@60Hz. [ 1.142847] 1920x1080p@50Hz. [ 1.142865] 1280x720p@60Hz. [ 1.142882] 1280x720p@50Hz. [ 1.142900] 720x576p@50Hz. [ 1.142916] 720x480p@60Hz. [ 1.142934] Support audio type: LPCM [ 1.142955] Support audio sample rate: [ 1.142977] 32000 [ 1.142990] 44100 [ 1.143003] 48000 [ 1.143016] Support audio word lenght: [ 1.143038] 16bit [ 1.143051] 20bit [ 1.143064] 24bit [ 1.143077] ******** Show Sink Info ******** [ 1.143123] rk3188 lcdc1 clk enable... [ 1.143154] lcdc1: dclk:148500000>>fps:60 [ 1.143181] rk30-lcdc rk30-lcdc.1: rk3188_load_screen for lcdc1 ok! [ 1.143221] lcdc1 wakeup from standby! [ 1.143246] lcdc1 win0 open,atv layer:1 [ 1.143277] lcdc1 win1 closed,atv layer:1 [ 1.244443] PPP MPPE Compression module registered [ 1.244483] NET: Registered protocol family 24 [ 1.244572] usbcore: registered new interface driver asix [ 1.244628] usbcore: registered new interface driver cdc_ether [ 1.244676] cdc_ncm: 04-Aug-2011 [ 1.244721] usbcore: registered new interface driver cdc_ncm [ 1.244756] Rockchip WiFi SYS interface (V1.00) ... [ 1.244814] Initializing USB Mass Storage driver... [ 1.244874] usbcore: registered new interface driver usb-storage [ 1.244912] USB Mass Storage support registered. [ 1.245017] usbcore: registered new interface driver usbserial [ 1.245074] USB Serial support registered for generic [ 1.245138] usbcore: registered new interface driver usbserial_generic [ 1.245178] usbserial: USB Serial Driver core [ 1.245290] USB Serial support registered for GSM modem (1-port) [ 1.245356] usbcore: registered new interface driver option [ 1.245391] option: v0.7.2:USB Driver for GSM modems [ 1.245449] USB Serial support registered for usi-modem [ 1.245504] usbcore: registered new interface driver usi-modem [ 1.467309] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.467351] usb20_otg usb20_otg: DWC OTG Controller [ 1.467460] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1 [ 1.467525] usb20_otg usb20_otg: irq 48, io mem 0x00000000 [ 1.467581] DWC_OTG: Init: Port Power? op_state=1 [ 1.467610] DWC_OTG: Init: Power Port (0) [ 1.467674] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.467716] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.467759] usb usb1: Product: DWC OTG Controller [ 1.467791] usb usb1: Manufacturer: Linux 3.0.36+ dwc_otg_hcd [ 1.467825] usb usb1: SerialNumber: usb20_otg [ 1.468147] hub 1-0:1.0: USB hub found [ 1.468181] hub 1-0:1.0: 1 port detected [ 1.470759] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xdf180000 [ 1.681321] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.681360] usb20_host usb20_host: DWC OTG Controller [ 1.681416] usb20_host usb20_host: new USB bus registered, assigned bus number 2 [ 1.681477] usb20_host usb20_host: irq 49, io mem 0x00000000 [ 1.681546] DWC_OTG: Init: Port Power? op_state=1 [ 1.681576] DWC_OTG: Init: Power Port (0) [ 1.681630] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.681674] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.681717] usb usb2: Product: DWC OTG Controller [ 1.681745] usb usb2: Manufacturer: Linux 3.0.36+ host20_hcd [ 1.681779] usb usb2: SerialNumber: usb20_host [ 1.682070] hub 2-0:1.0: USB hub found [ 1.682100] hub 2-0:1.0: 1 port detected [ 1.682469] DWC_OTG: Mode Mismatch Interrupt: currently in Host mode [ 1.755603] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 1.755650] android_usb gadget: Number of LUNs=2 [ 1.755688] lun0: LUN: removable file: (no medium) [ 1.755718] lun1: LUN: removable file: (no medium) [ 1.755939] android_usb gadget: android_usb ready [ 1.756128] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0 [ 1.756368] usbcore: registered new interface driver xpad [ 1.756534] =================================================== [ 1.756572] Rockchip IR remote controller driver. Version 1.0.0 [ 1.756608] =================================================== [ 1.756642] ++++++++remotectl_init [ 1.756691] ++++++++remotectl_probe [ 1.756730] remotectl probe j=0x0 [ 1.756753] remotectl probe j=0x1 [ 1.756774] remotectl probe j=0x2 [ 1.756797] remotectl probe j=0x3 [ 1.756820] remotectl probe j=0x4 [ 1.756841] remotectl probe j=0x5 [ 1.756862] remotectl probe j=0x6 [ 1.756988] input: rkxx-remotectl as /devices/platform/rkxx-remotectl/input/input1 [ 1.759135] rtc_hym8563 1-0051: clock/calendar information is no longer guaranteed [ 1.761836] using rtc device, rtc_hym8563, for alarms [ 1.761885] rtc_hym8563 1-0051: rtc core: registered rtc_hym8563 as rtc0 [ 1.761950] i2c /dev entries driver [ 1.762423] lirc_dev: IR Remote Control driver registered, major 250 [ 1.762464] IR NEC protocol handler initialized [ 1.762493] IR RC5(x) protocol handler initialized [ 1.762523] IR RC6 protocol handler initialized [ 1.762551] IR JVC protocol handler initialized [ 1.762578] IR Sony protocol handler initialized [ 1.762609] IR RC5 (streamzap) protocol handler initialized [ 1.762642] IR LIRC bridge handler initialized [ 1.762670] Linux video capture interface: v2.00 [ 1.762753] usbcore: registered new interface driver uvcvideo [ 1.762787] USB Video Class driver (v1.1.0) [ 1.762837] def_ref_volt: 1800mV, curr_ref_volt: 1800mV [ 1.763154] device-mapper: uevent: version 1.0.3 [ 1.763360] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 1.763545] Bluetooth: HCI UART driver ver 2.2 [ 1.763575] Bluetooth: HCI H4 protocol initialized [ 1.763606] Bluetooth: HCILL protocol initialized [ 1.763759] cpuidle: using governor ladder [ 1.763791] cpuidle: using governor menu [ 1.809247] [ 1.809250] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc0] [ 1.814354] rk29_sdmmc_change_clk_div..1681.. newDiv=62, newCLK=299Khz [sd_mmc] [ 1.814423] .Line4005..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sd_mmc] [ 1.814623] .Line4005..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sdio] [ 1.815998] usbcore: registered new interface driver usbhid [ 1.816036] usbhid: USB HID core driver [ 1.816337] logger: created 256K log 'log_main' [ 1.816430] logger: created 256K log 'log_events' [ 1.816511] logger: created 256K log 'log_radio' [ 1.816598] logger: created 256K log 'log_system' [ 1.816919] zram: Created 1 device(s) ... [ 1.817376] ALSA device list: [ 1.817396] No soundcards found. [ 1.817499] GACT probability NOT on [ 1.817528] Mirror/redirect action on [ 1.817556] u32 classifier [ 1.817573] Actions configured [ 1.817595] Netfilter messages via NETLINK v0.30. [ 1.817660] nf_conntrack version 0.5.0 (13658 buckets, 54632 max) [ 1.817990] ctnetlink v0.93: registering with nfnetlink. [ 1.818051] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 1.818093] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 1.818363] xt_time: kernel timezone is -0000 [ 1.818517] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.818673] arp_tables: (C) 2002 David S. Miller [ 1.818738] TCP cubic registered [ 1.818760] Initializing XFRM netlink socket [ 1.819133] NET: Registered protocol family 10 [ 1.819716] Mobile IPv6 [ 1.819751] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.819887] IPv6 over IPv4 tunneling driver [ 1.820461] NET: Registered protocol family 17 [ 1.820513] NET: Registered protocol family 15 [ 1.855038] [ 1.855041] mmc_attach_sd..1230.. ===== Begin to identify card as SD-card. [mmc0] [ 1.907866] rk29_sdmmc_change_clk_div..1681.. newDiv=0, newCLK=37125Khz [sd_mmc] [ 1.907956] mmc0: new high speed SDHC card at address e624 [ 1.908237] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 1.908613] Bluetooth: RFCOMM TTY layer initialized [ 1.908654] Bluetooth: RFCOMM socket layer initialized [ 1.908736] Bluetooth: RFCOMM ver 1.11 [ 1.908770] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.908804] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.908947] NET: Registered protocol family 35 [ 1.909141] [BT_RFKILL]: Enter rfkill_rk_init [ 1.909238] [BT_RFKILL]: Request irq for bt wakeup host [ 1.909282] [BT_RFKILL]: ** disable irq [ 1.910196] [ 1.910199] msdos_partition..466... ==== Begin to parse sdcard-partition. [mmcblk0] [ 1.910252] msdos_partition..535... ==== The sdcard has MBR. [mmcblk0] [ 1.910291] msdos_partition..548... ==== partition-1, size=1959MB. [mmcblk0] [ 1.910332] msdos_partition..576... ==== main partition-1....[mmcblk0] [ 1.910371] mmcblk0: p1 [ 1.910694] sdmmc_rescan_try_freq..1909.. ===== Initialize SD-card successfully. [mmc0] [ 1.910753] [ 1.910756] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc1] [ 1.925235] rk29_sdmmc_change_clk_div..1681.. newDiv=42, newCLK=294Khz [sdio] [ 1.935224] [BT_RFKILL]: bt shut off power [ 1.935252] [BT_RFKILL]: ap6210 device registered. [ 1.935322] pmic set pm_suspend_volt: [ 1.935351] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.935412] Registering SWP/SWPB emulation handler [ 2.065239] usb 2-1: new low speed USB device number 2 using usb20_host [ 2.282737] ddrfreq: change freq to 300 MHz when normal [ 2.282776] ddrfreq: verion 3.2 20131126 [ 2.282807] ddrfreq: fix cpu pause bug [ 2.282836] ddrfreq: normal 300MHz video 0MHz video_low 0MHz duakvie: cMH' clea0e d rustend '9deH':rFioe xisMH [ 2.283749] rtc_hym8563 1-0051: setting system clock to 2011-01-01 12:00:01 UTC (1293883201) [ 2.286576] asoc: rk-hdmi-i2s-hifi <-> rk29_i2s.1 mapping ok [ 2.287063] usbcore: registered new interface driver snd-usb-audio [ 2.287214] Freeing init memory: 168K [ 2.292872] usb 2-1: New USB device found, idVendor=413c, idProduct=2105 [ 2.292920] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.292969] usb 2-1: Product: Dell USB Keyboard [ 2.293000] usb 2-1: Manufacturer: Dell [ 2.313616] input: Dell Dell USB Keyboard as /devices/platform/usb20_host/usb2/2-1/2-1:1.0/input/input2 [ 2.314018] generic-usb 0003:413C:2105.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-usb20_host-1/input0 [ 2.353066] ======================================================= [ 2.353108] ==== Launching Wi-Fi driver! (Powered by Rockchip) ==== [ 2.353145] ======================================================= [ 2.353186] RKWIFI WiFi driver (Powered by Rockchip,Ver 4.53.WFD) init. [ 2.353253] =========== WLAN placed in POWER ON ======== [ 2.353327] ANDROID-ERROR) wifi_set_power = 1 [ 2.353359] rk29sdk_wifi_power: 1 [ 2.603581] wifi turn on power [ 2.603605] ANDROID-ERROR) wifi_set_carddetect = 1 [ 2.603645] rk29sdk_wifi_set_carddetect:1 [ 2.603673] mmc1: slot status change detected(0-1) [ 2.795246] [ 2.795249] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc1] [ 2.839122] [ 2.839125] mmc_attach_sdio..1112.. ===== Begin to identify card as SDIO-card. [mmc1] [ 2.875619] rk29_sdmmc_change_clk_div..1681.. newDiv=0, newCLK=24750Khz [sdio] [ 2.876902] mmc1: new high speed SDIO card at address 0001 [ 2.877127] sdmmc_rescan_try_freq..1863.. ===== Initialize SDIO successfully. [mmc1] [ 2.877159] Linux Kernel SDIO/MMC Driver [ 2.877281] [ 2.877284] Dongle Host Driver, version 1.28.13.1.1 (r) [ 2.877291] Compiled in drivers/net/wireless/bcmdhd on Jul 4 2013 at 10:32:45 [ 14.875231] dhd_module_init: sdio_register_driver timeout or error [ 14.875352] ANDROID-ERROR) ## wifi_remove [ 14.875379] ANDROID-ERROR) wifi_set_power = 0 [ 14.875411] rk29sdk_wifi_power: 0 [ 15.076345] wifi shut off power [ 15.076370] ANDROID-ERROR) wifi_set_carddetect = 0 [ 15.076408] rk29sdk_wifi_set_carddetect:0 [ 15.076436] mmc1: slot status change detected(1-0) [ 15.076544] mmc1: card 0001 removed [ 15.076601] [ 15.076604] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc1] [ 15.076697] =========== WLAN placed in POWER OFF ======== [ 15.095249] rk29_sdmmc_change_clk_div..1681.. newDiv=42, newCLK=294Khz [sdio] insmod: can't insert '/lib/modules/rkwifi.ko': No such device [ 15.177483] EXT3-fs (mmcblk0p1): error: couldn't mount because of unsupported optional features (240) [ 15.228691] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities [ 18.474975] EXT4-fs (mmcblk0p1): recovery complete [ 18.478704] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 19.391645] init: ureadahead main process (82) terminated with status 5 [ 19.521050] init: mounted-proc main process (91) terminated with status 1 speech-dispatcher disabled; edit /etc/default/speech-dispatcher saned disabled; edit /etc/default/saned